MORE THAN A MILLION SOLUTIONS
Our unique fan design and order management systems allow us to configure our fans to specific customer needs, while maintaining a high degree of standardization. We can thus supply customized solutions based on standard components – at very competitive prices.
We concentrate on robust and reliable products, which receive thorough testing prior to delivery. Even large and complex solutions can be supplied as pre-assembled units, greatly simplifying installation.
The ‘XOE’ fan is Berg Jet’s signature product, designed for optimal efficiency. In recent years, our customers have expressed greater interest in reducing energy costs. For this reason, we have increased our emphasis on fan input power requirements. We have successfully designed and produced fan systems capable of saving our customers valuable kilowatt hours, resulting in substantial economic savings.
Considering the amount of power fans typically consume and concerns over the cost of energy, it is vital that each fan be properly sized and rated. Our expert engineers possess the experience, technical knowledge and judgement required to determine a fan’s efficiency and performance value. XOE fans can be optimized to match your specific operating point.
SCOPE
The XOE range is suitable for medium pressure and high pressure from 1,000 Pa to 15,000 Pa.
In terms of volume, the XOE range spans 5,000 m3/h to 200,000 m3/h.
The XOE range is designed for operating temperatures up to 600 °C with cooling discs and customized versions available upon request.
The impeller can be mounted directly on the motor shaft or on a shaft with coupling and bearings. A solution with belt drive is also available with the motor mounted either above the fan shaft or below on a stand on the common base frame.
CERTIFIED MATERIALS
The standard fan casing is made from mild carbon steel, S235JR (EN10025). The impeller is made from carbon steel, S235JR (EN10025) or Corten steel. The fan frame is made from carbon steel, S235JR (EN10025). The shaft is centreless ground Ceax steel as standard, type C45E. Various shields are made from carbon steel, S235JR (EN10025). Electrode welding with mild steel wire and flux wire (AWS A5.22/SFA 5.22). The OE range may also be made from Corten-A as well as various types of stainless steel.
SURFACE TREATMENT
A standard Berg Jet fan is primed and finished with alkyd top coat RAL 7001 with total thickness of 80 µm. Flue gas fans are finished with black heat-resistant paint. This scheme complies with corrosion class 1. Other colours or paint schemes are available according to the assignment.
Fans in stainless steel will be glass blasted as standard. On request, stainless steel fans can be supplied with the surface pickled.
QUALITY CONTROL
Welding certificates can be presented on request.
The fan wheel is balanced in accordance with ISO 1940-1 with a balance quality grade of at least G 6,3. Vibrations on the fan (fan wheel, motor, pulleys, cooling discs, etc.) are tested in accordance with ISO 14694 and ISO 10816-3. The fan undergoes final testing in accordance with customer specifications. Electricity consumption, power consumption, speed and static pressure are all measured.
Berg Jet can perform classification of fan and motor at the customer’s request.
STANDARDS
The fans comply with the EU Machinery Directive (98/37/EF).
ACCESSORIES
- Motors (comply with the EU Low Voltage Directive (73/23/EF))
- Flexible connections for input and output as well as wear plates
- Vibration dampers
- Multiblade damper and actuators
- Inspection hatch and drain
- Shaft seals
- Silencers
- Insulation of fans and acoustic enclosures
- Frequency converters (comply with the EU EMC Directive (89/336/EEC))
The efficient ‘XMP fan’ is a particularly robust fan for clean and less dusty air. This fan type is used in small and medium-sized industrial plants, in comfort and industrial ventilation and various filter systems.
SCOPE
There are 15 different frame sizes in the XMP range, and each size is available in various models.
The XMP range is suitable for medium pressure and high pressure from 500 Pa to 15,000 Pa.
In terms of volume, the XMP range spans from 100 m3/h to 80,000 m3/h.
The XMP range is designed for operating temperatures up to 600 °C with cooling discs and customized versions are available.
The impeller can be mounted directly on the motor shaft or on a shaft with coupling and bearings. A solution with belt drive is also available with the motor mounted either above the fan shaft or below on a stand on the common base frame.
CERTIFIED MATERIALS
As standard the fan casing is made from mild carbon steel, S235JR (EN10025). The impeller is made from carbon steel, S235JR (EN10025) or Corten steel. The fan frame is made from carbon steel, S235JR (EN10025). The shaft is centreless ground Ceax steel as standard, type C45E. Various shields are made from carbon steel, S235JR (EN10025). Electrode welding with mild steel wire and flux wire (AWS A5.22/SFA 5.22). The XMP range may also be made from Corten-A as well as various types of stainless steel.
SURFACE TREATMENT
A standard Berg Jet fan is primed and finished with alkyd top coat RAL 7001 with total thickness of 80 µm. Flue gas fans are finished with black heat-resistant paint. This scheme complies with corrosion class 1. Other colours or paint schemes are available according to the assignment.
Fans in stainless steel will be glass blasted as standard. On request, stainless steel fans can be supplied with the surface pickled.
QUALITY CONTROL
Welding certificates can be presented on request.
The fan wheel is balanced in accordance with ISO 1940-1 with a balance quality grade of at least G 6,3. Vibrations on the fan (fan wheel, motor, pulleys, cooling discs, etc.) are tested in accordance with ISO 14694 and ISO 10816-3. The fan undergoes final testing in accordance with customer specifications. Electricity consumption, power consumption, speed and static pressure are all measured.
Berg Jet can perform classification of fan and motor at the customer’s request.
STANDARDS
The fans comply with the EU Machinery Directive (98/37/EF).
ACCESSORIES
- Motors (comply with the EU Low Voltage Directive (73/23/EF))
- Flexible connections for input and output as well as wear plates
- Vibration dampers
- Multiblade damper and actuators
- Inspection hatch and drain
- Shaft seals
- Silencers
- Insulation of fans and acoustic enclosures
- Frequency converters (comply with the EU EMC Directive (89/336/EEC))
The ‘XHP’ fan is designed for high pressure purposes, while maintaining optimum efficiency. This model is used in small industrial plants, as well as comfort and industrial ventilation and various filter systems, where high pressure air at small volumes is needed.
SCOPE
There are 14 frame sizes in the XHP range, and each size is available in various models.
The XHP range is suitable for medium and high pressure from 100 Pa to 1,500 Pa.
In terms of volume, the XHP range spans from 1,000 m3/h to 15,000 m3/h.
The XHP range is designed for operating temperatures up to 600 °C with cooling discs and customized versions are available.
The impeller can be mounted directly on the motor shaft or on a shaft with coupling and bearings. A solution with belt drive is also available with the motor mounted either above the fan shaft or below on a stand on the common base frame.
CERTIFIED MATERIALS
As standard, the fan casing is made from mild carbon steel, S235JR (EN10025). The impeller is made from carbon steel, S235JR (EN10025) or Corten steel. The fan frame is made from carbon steel, S235JR (EN10025). The shaft is centreless ground Ceax steel as standard, type C45E. Various shields are made from carbon steel, S235JR (EN10025). Electrode welding with mild steel wire and flux wire (AWS A5.22/SFA 5.22). The XHP range may also be made of Corten-A as well as various types of stainless steel.
SURFACE TREATMENT
A standard Berg Jet fan is primed and finished with alkyd top coat RAL 7001 with total thickness of 80 µm. Flue gas fans are finished with black heat-resistant paint. This scheme complies with corrosion class 1. Other colours or paint schemes are available according to the assignment.
Fans in stainless steel will be glass blasted as standard. On request, stainless steel fans can be supplied with the surface pickled.
QUALITY CONTROL
Welding certificates can be presented on request.
The fan wheel is balanced in accordance with ISO 1940-1 with a balance quality grade of at least G 6,3. Vibrations on the fan (fan wheel, motor, pulleys, cooling discs, etc.) are tested in accordance with ISO 14694 and ISO 10816-3. The fan undergoes final testing in accordance with customer specifications. Electricity consumption, power consumption, speed and static pressure are all measured.
Berg Jet can perform classification of fan and motor at the customer’s request.
STANDARDS
The fans comply with the EU Machinery Directive (98/37/EF).
ACCESSORIES
- Motors (comply with the EU Low Voltage Directive (73/23/EF))
- Flexible connections for input and output as well as wear plates
- Vibration dampers
- Multiblade damper and actuators
- Inspection hatch and drain
- Shaft seals
- Silencers
- Insulation of fans and acoustic enclosures
- Frequency converters (comply with the EU EMC Directive (89/336/EEC))
The ‘XLP’ fan is built to last, and well-suited for transporting clean air. Our fans are often running on a 24-hour basis, and have been known to outlive our competitors’. The XLP model is used in small and medium-sized industrial plants, in comfort and industrial ventilation and various filter systems.
SCOPE
There are 15 frame sizes in the XLP range, and each size is available in various models.
The XLP range is suitable for low pressures from 200 Pa to 2,000 Pa.
In terms of volume, the XLP range spans from 100 m3/h to 50,000 m3/h.
The XLP range is designed for operating temperatures up to 600 °C with cooling discs and customized versions are available.
The impeller can be mounted directly on the motor shaft or on a shaft with coupling and bearings. A solution with belt drive is also available with the motor mounted either above the fan shaft or below on a stand on the common base frame.
CERTIFIED MATERIALS
As standard the fan casing is made from mild carbon steel, S235JR (EN10025). The impeller is made from carbon steel, S235JR (EN10025) or Corten steel. Up to dia. 515 mm, the impeller may be manufactured in aluminium. The fan frame is made from carbon steel, S235JR (EN10025). The shaft is centreless ground Ceax steel as standard, type C45E. Various shields are made from carbon steel, S235JR (EN10025). Electrode welding with mild steel wire and flux wire (AWS A5.22/SFA 5.22). The XLP range may also be made of Corten-A as well as various types of stainless steel.
SURFACE TREATMENT
A standard Berg Jet fan is primed and finished with alkyd top coat RAL 7001 with total thickness of 80 µm. Flue gas fans are finished with black heat-resistant paint. This scheme complies with corrosion class 1. Other colours or paint schemes are available according to the assignment.
Fans in stainless steel will be glass blasted as standard. On request, stainless steel fans can be supplied with the surface pickled.
QUALITY CONTROL
Welding certificates can be presented on request.
The fan wheel is balanced in accordance with ISO 1940-1 with a balance quality grade of at least G 6,3. Vibrations on the fan (fan wheel, motor, pulleys, cooling discs, etc.) are tested in accordance with ISO 14694 and ISO 10816-3. The fan undergoes final testing in accordance with customer specifications. Electricity consumption, power consumption, speed and static pressure are all measured.
Berg Jet can perform classification of fan and motor at the customer’s request.
STANDARDS
The fans comply with the EU Machinery Directive (98/37/EF).
ACCESSORIES
- Motors (comply with the EU Low Voltage Directive (73/23/EF))
- Flexible connections for input and output as well as wear plates
- Vibration dampers
- Multiblade damper and actuators
- Inspection hatch and drain
- Shaft seals
- Silencers
- Insulation of fans and acoustic enclosures
- Frequency converters (comply with the EU EMC Directive (89/336/EEC))
DESIGNED TO SUIT YOUR NEEDS
Berg Jet “Custom Fit” fans are engineered and manufactured for specific projects. We create the absolute optimal solution under the given conditions by fulfilling project demands with regard to:
- Minimal power consumption
- Lowest revolutions, resulting in lowest maintenance costs
- Physical limitations
- Minimal noise
- High temperature solutions
- Aggressive media solutions
Each Berg Jet fan is carefully designed using our unique Custom Fit system, which enables us to create fans that optimally meet your exact operating point(s).. During the design phase, your fan is perfected for your requirements, allowing us to present the optimal solution under the given conditions. Berg Jet delivers Custom Fit fans designed with airflow of up to 900.000 m3/hand motor effect up to 1,5 MW.
ADDITIONAL CUSTOMIZATION
Fan casing Steel/Aisi304/316/3 21
Impeller: Steel/Aisi304/316/3 21
Surface Glass blasting, Polishing, Epoxy treatment, Porcelain
Certified Welding procedures: Full welding, Seal welding, Pickling
All leading Classification societies: DNV, GL, LRS, BV, RINA, CCS, ABS, Class NK, RMRS
Meeting customer noise requirements: Attenuators, Noise proof cabinets
Insulation: AISI 304, 316, galv. steel
Systems: Fan and Motor accessories
